MRIGESHWAR KUMAR

Resourceful and field-exposed Mechanical Engineer with cross-functional experience in LPG plant operations, preventive maintenance, safety compliance, and client engagement. Trained at HPCL's LPG Bottling Plant in Bokta, Gorakhpur, gaining practical knowledge of mechanical systems, utilities, and bottling line automation.

Later worked in client-facing roles at Square Yards, enhancing communication, negotiation, and analytical skills. Familiar with modern mechanical tools such as 5S, RCA, TPM basics, and safety protocols like OISD and PTW systems. Looking to leverage both technical exposure and communication strength in a challenging engineering environment. Knowledgeable in latest mechanical engineering terminology and practices

Motivated and detail-oriented Mechanical Engineer seeking a challenging role in a forward-thinking organization where I can apply my academic knowledge, industrial exposure, and hands-on project experience to contribute to operational excellence, innovation, and sustainable development. Passionate about integrating core engineering principles with modern industrial practices to solve real-world problems and drive continuous improvement.

• Designed a working prototype of a single-cylinder compressed air engine to power a bicycle
• Modified an existing IC engine by replacing the combustion chamber with an air inlet valve
• Developed a compact air tank and controlled air flow using solenoid valves and timing control
• Achieved short-distance travel using stored high-pressure air without any fuel combustion
• Applied thermodynamics, valve timing, and air expansion principles in engine performance
• Promoted as a clean transportation alternative producing zero emissions and minimal noise
• Recognized in innovation conclave for showcasing green vehicle technology on low budget

• Designed and fabricated a pedal-powered centrifugal water pump system for rural irrigation and domestic use
• Developed a chain and sprocket drive integrated with a mild steel frame for mechanical power transmission
• Achieved a water discharge rate of 15–20 L/min from shallow sources using manual pedaling
• Applied concepts of centrifugal pump mechanics, energy conversion, torque-speed ratio, and human ergonomics
• Used a pulley and belt system with adjustable tension to regulate pump performance as per water head
• Promoted sustainable engineering and affordable innovation for off-grid areas and relief camps
• Recognized by project panel for practical problem-solving and mechanical design thinking

• Developed a parabolic reflector-based solar thermal cooker for clean and fuel-free outdoor cooking
• Designed a mild steel parabolic dish with aluminum reflective surface to concentrate solar rays
• Achieved up to 300°C at the focal point, capable of boiling water in under 12 minutes
• Applied principles of solar geometry, heat transfer, and thermal efficiency
• Ensured structural stability with wind-resistant base and angular adjustment for solar tracking
• Ideal for use in rural areas, camps, and eco-friendly kitchens to reduce firewood/LPG usage
• Recognized in campus exhibition for practical environmental innovation and renewable energy utilization

• Fabricated a table-top hydraulic press using Pascal’s Law for forming and punching light gauge sheets
• Designed for educational and prototyping use with a manually operated hydraulic jack system
• Focused on compact design, low-cost build, and basic safety features

• Designed an LDR-based solar panel tracker using Arduino to adjust angle based on sunlight direction
• Increased panel efficiency by ~30% over fixed panels in testing conditions
• Integrated servo motors, power circuit, and light detection logic for automatic adjustment

• Created a platform that converts human foot pressure into electrical energy using rack-pinion & flywheel system
• Targeted use in crowded places like railway stations and malls for low-power applications
• Stored energy into rechargeable battery for later use in LED lighting

• Industrial Training at HPCL – Bokta (Mechanical Systems & Utilities)
• Sales & Client Handling Certification (Square Yards Internal Program)
• Self-study: 5S, TPM Basics, RCA, LPG Safety (YouTube & Industry PDFs)
• Awareness Modules: Industry 4.0, FMEA, Poka-Yoke, CMMS Tools
• AutoCAD 2D/3D (Professional Training)
• SolidWorks (Modeling & Simulation)
• Introduction to Manufacturing Processes

• Career Break Activities (2022 – Present)
• - Prepared for UPSC Civil Services, enhancing critical thinking and analytical abilities.
• - Undertook self-paced learning in CAD tools, simulation techniques, and industry standards.
• - Continued disciplined equity trading for financial management and strategy refinement.

Languages: Hindi, English

Hobbies: Classical/Bollywood Singing, Exploring new places, Learning new skills

I hereby declare that the information provided above is true and correct to the best of my knowledge. 

(Mrigeshwar Kumar)                                                                         Date -      

 Place -