Safa Ullah

TACO prestolite electric company is a part of tata group company which design development and manufacture power train (motor+inverter+reducer ) of electric vehicle.

• Involved in design and development testing of power train of vehicle like TATA NEXON, Tiago, TATA punch , TATA curvv .
• Design and development of MCU (motor control unit) unit for 4-wheeler BEV
• Design and development of traction motor for 3 and 4-wheeler
• Responsible of MCU testing with motors, E-drive (PMSM, IM)
• Responsible for testing and validation of product (MCU, MOTOR, E-DRIVE)
• Responsible for high -low voltage motor testing, efficiency, NVH testing, performance, back EMF, short circuit, peak and rated power test, EOL test and regeneration
• Responsible of software and, UDS, FOTA testing
• Responsible and take care of design and verification plan (DVP)of products
• Responsible for certification and homologation of product from certified agency like ARAI, ICAT as per standard, AIS004_3, AIS 039, AIS ,041, AIS 048
• Responsible for EMI/EMC testing/validation both vehicle and component level
• Working on CAN communication, CAN tool, vector tool, can tester
• Responsible for documentation and certification of AIS, ISO.IEC tests
• Responsible for environment testing as per different IEC, ISO, GB/T Standards
• Responsible for set up new testing facility dynamometer, E-axle, climate chamber
• Knowledge about power analyzer, oscilloscope, Current sensor, voltage sender, Gradient test, climate chamber test, IP 65, IP67, IP68.

Sterling G take E-mobility is a company which manufacture and develop MCU unit (motor control unit) for Electrical vehicle 2W ,3W,4wheeler and provide support in development of electric vehicle.

• Design and development of MCU (motor control unit) unit for 2-wheeler ,3-wheeler and 4-wheeler BEV
• Responsible of MCU testing with motors (BLDC, PMSM, IM)
• Involving in MCU development
• Responsible for high voltage motor testing
• Responsible and take care design and verification plan of products
• Responsible for regeneration, performance, peak power, rated power and peak current and rated current tests
• Responsible for certification and homologation of product from ARAI, ICAT, certified labs, AIS004_3, AIS 039, AIS ,041, AIS 048
• Responsible for documentation and certification of AIS, ISO.IEC tests
• Responsible for EMI/EMC testing/validation both vehicle and component level
• Responsible for environment tests as per different IEC, ISO Standards
• Responsible for arranging new motor test facilities, labs as requirement.

AVL is the world's largest independent company for the development of powertrain systems with

Internal combustion engines / electrical vehicle /battery/ inverter as well as instrumentation and test systems AVL Test Systems and AVL Advanced Simulation Technologies enable the development of highly creative, mature, and application-specific solutions for customers in order that they meet their future market challenges.

Profile summary

1. Having Emission Application knowledge required for Euro 6 / Bharat stage6

2. Having electrical vehicle application knowledge required for different types of power and load testing.

3. Have a working experience on EV testing system and expertise in motor (PMSM, BLDC), inverter, battery (Li-ion, lead acid) testing.

4. Knowledge about voltage, current, power measurement of Electrical vehicle.

5. Having knowledge about BMS /CAN communication protocols.

6. Knowledge about battery testing like, Test for Capacity, Vibration Test, Shock Test, Penetration Test (Cell Level or Battery module)

7. Able to handle /planning of service and commissioning, AMC of engine /EV vehicle test bed / utility.

8. Having experience of working on dynamometers like Eddy current dynamometer, Chassis dynamometer, transient dynamometer and their control cabinets, good knowledge about configuration of dynamometers with automation system, also have troubleshooting, maintenance, commissioning experience.

9. having working experience on internal combustion engine, light duty and heavy-duty engine emission testing and have knowledge about EUROPIAN STATIONARY CYCLE (ETC) and EUROPIAN TRANSIENT CYCLE, BS6, IDC cycle.

10. Have a experience of working on internal combustion engine test bed, installation, commissioning maintenance, troubleshooting of below system.

11. Smoke measurement (AVL smoke meter, AVL Opacimeter, AVL MSS), fuel measurement device, Automation system (AVL PUMA, EDACS, LYNX,), Particulate counter (AVL APC), coolant and fuel conditioning system, intake air condition system (ACS). Urea measurement system (Pl urea)

Blow my meter (AVL 442S).

KEY RESPONSIBILITY

· Installation, commissioning and service support for.

1. Electrical vehicle test bed system (battery, inverter, motor)

2. Provide technical support on engine /vehicle test beds

3. fuel cell test bed system (PEM, DMFC, HTPEM)

4. Gasoline / Diesel emission measurement system

5. Gasoline / Diesel Engine testing Automation System

6. Gasoline / Diesel Fuel, Air, measurement system

7. Dynamometer (active and passive)

8. Gasoline / diesel particulate measurement system