SARAVANAN S

1) Installation, Testing, Commissioning, Operation and Maintenance of following Electrical Equipments in Electrical Distribution Systems.

a. 11 kV High Tension Panels

b. 11 kV Vacuum Circuit Breakers

c. 11 kV / 433 V ONAN Transformers

d. 11 kV / 433 V Cast Resin Dry Type Transformers

e. 415 V Low Tension Power Control Center Panels

f. 415 V Low Tension Motor Control Center Panels

g. 415 V Low Tension Automatic Mains Failure Panels

h. 415 V Prime Rated Emergency Diesel Generator Sets

i. 415 V Street Light Energy Saver Panels

j. 415 V Power Factor Improvement Panels

k. 415 V Digital Addressable Lighting Interface Panels

l. 415 V PLC cum LDR cum Timer Controlled Street Light and Area Light Control Panel

m. Electromagnetic Protection Relays

n. Electromechanical Protection Relays

o. Numerical Protection Relays

p. Internal Arc Protection Relays

q. ON Grid Solar Photovoltaic Panels cum Solar ON Grid Inverters

r. Solar Thermal Water Heater Panels

s. Passenger and Stretcher Lifts for High Rise Buildings up to G+15 Storey Buildings

2) Establishment and Study of the following in the Electrical Distribution Systems

a. Establishment of Optical Fibre Cable Network

b. Establishment of Passive Network Components

c. Establishment of Active Network Components

d. Establishment of Power Line Carrier Communication Network

e. Establishment of Modbus Protocol using RS485 Communication Network Port

f. Remote Monitoring of all the Parameters in Electrical Distribution Systems

g. Conceptual Design for Supervisory Control and Data Acquisition Systems

h. Symmetrical and Asymmetrical Fault Analysis in 11 kV Electrical Distribution Systems

i. Forecasting of Electrical Load Growth

j. Indoor and Outdoor Illumination Study

k. Data Collection pertaining to Energy Audit

l. Data Collection pertaining to Electricity Consumption and Electricity Demand

m. Incorporation of Energy Saving and Energy Conservation Techniques

n. Incorporation of Fire Alarm Systems for High Rise Buildings, Hospitals etc.

o. Incorporation of Energy Efficient LED Street, Area and Flood Lights into the System

p. Incorporation of Energy Efficient Fans, Motors into the System

q. Solving Problems encountered in the System using Quality Circle Tools.

1) Manufacturing of Miniature Circuit Breakers

2) Manufacturing of Residual Current Circuit Breakers

3) Compliance of ISO 9001 and ISO 14001

4) Quality Circle Techniques

5) Implementation of 5S Techniques

6) Finding out Root Cause Analysis of products returned by Customers

7) Data Collection and Maintenance of Inventory

8) Daily SAP Clearance

9) Preparation of Skill Set Matrix of all the Workmen

10) Implementation of innovative ideas to enhance the production targets

1) Designing of Power Control Centres and Motor Control Centres using PRO-E Software.

2) Testing of Air Circuit Breakers, Moulded Case Circuit Breaker and Power Contactors

1) Installation, Testing, Commissioning, Operation and Maintenance of following Electrical Equipments in Electrical Distribution Systems.

a. All Electrical Equipments installed at 450 Tonnes per Hour Crushing Plant

i. Slip Ring Induction Motors up to 500 H.P

ii. Squirrel Cage Induction Motors up to 125 H.P

iii. Synchronised Diesel Generator Sets up to 1000 kVA

iv. Rotor Resistance Starters

v. Star-Delta Starters

vi. Direct-on-line Starters

vii. Variable Voltage Variable Frequency Drives

viii. Motor Control Centre Panels

ix. Power Control Centre Panels

x. Programming Logic Controller Panels

xi. Reverse Power Relays

b. All Electrical Equipments installed at Ice Plants

c. All Electrical Equipments installed at Chilling Plants

d. All Electrical Equipments installed at Concrete Batching Plants

2) Internal Electrification of Toll Plaza Control Room

3) CCTV Network in National Highways

4) Overload and Overspeed Sensors in National Highways

5) Highway Outdoor Lighting